characteristic TDS3000C series electrical characteristics
TDS3012CTDS3014CTDS3032CTDS3034CTDS3052CTDS3054C
| bandwidth |
100 MHz |
100 MHz |
300 MHz |
300 MHz |
500 MHz |
500 MHz |
| Calculated rise time (typical value) |
3.5 ns |
3.5 ns |
1.2 ns |
1.2 ns |
0.7 ns |
0.7 ns |
| Number of channels |
two |
four |
two |
four |
two |
four |
| External trigger input |
All models include |
| Sample rate per channel |
1.25 GS/s |
1.25 GS/s |
2.5 GS/s |
2.5 GS/s |
5 GS/s |
5 GS/s |
| Large record length |
10 k sample points |
| Vertical resolution |
9 bits |
| Vertical sensitivity, 1 M Ω |
1 mV/div to 10 V/div |
| Vertical sensitivity, 50 Ω |
1 mV/div to 1 V/div |
| Input coupling |
AC, DC, GND |
| Input impedance |
1 M Ω when 13 pF or 50 Ω terminals are connected in parallel |
| DC gain accuracy |
2% |
| Large input voltage (1 M Ω) |
150 VRMS, peak value ≤ 400 V |
| Large input voltage (50 Ω) |
5 VRMS, peak value ≤ 30 V |
| Positioning range |
5 div |
| Bandwidth limit |
20 MHz |
20 MHz |
20 MHz, 150 MHz |
20 MHz, 150 MHz |
20 MHz, 150 MHz |
20 MHz, 150 MHz |
| Time base range |
4 ns to 10 s |
4 ns to 10 s |
2 ns to 10 s |
2 ns to 10 s |
1 ns to 10 s |
1 ns to 10 s |
| Time base precision |
At any 1 ms interval± 20 ppm |
| Input/output interface |
| Ethernet port |
RJ-45 connector, supporting 10Base-T LAN |
| USB port |
Front panel USB 2.0 host port, supporting USB flash memory |
| GPIB port |
Comprehensive call/answer mode, setting and measurement (optional for TDS3GV communication module) |
| RS-232-C port |
DB-9 male connector, comprehensive sending/receiving mode; Control all modes, setting and measuring baud rate 38400 (optional for TDS3GV communication module) |
| VGA video port |
DB-15 female connector, monitor output, direct display of information on a large monitor equipped with VGA (TDS3GV communication module optional) |
| External trigger input |
BNC connector, input impedance>1 M Ω, parallel current 17 pF; Large input voltage 150 VRMS |
Acquisition mode
| DPO |
Capture and display complex waveforms, random events, and subtle patterns in actual signal behavior. DPO can display, store and analyze the three-dimensional information of signals in real time, namely amplitude, time and amplitude distribution in each period. |
| Peak detection |
Capture high frequency and random burrs. Burrs as narrow as 1 ns can be captured. |
| WaveAlert® |
Monitor the input signal on all channels and warn the user when any waveform deviates from the captured normal waveform occurs. |
| sampling |
Data sampling only. |
| average value |
Average 2 to 512 (optional) captured waveform data |
| envelope |
The large/small value obtained on one or more acquisition signals. |
| Single Sequence |
Use the Single Sequence button to capture a single triggered capture sequence at a time. |
Trigger system
| Main triggering methods |
Automatic triggering (supports 40ms/lattice and slower scrolling mode), normal triggering, and single sequence triggering. |
| B trigger |
Triggered after a time or event. |
| Time trigger range |
13.2 ns to 50 s |
| Event trigger range |
1 to 9999999 events. |
Trigger Type
| edge |
Conventional level driven trigger. Positive and negative slopes on any channel. Coupling selection: DC, noise suppression, high-frequency suppression, low-frequency suppression. |
| video |
It can be triggered on all lines or single lines of NTSC, PAL, SECAM, odd/even or all fields. |
| Extend Video |
Can be triggered on broadcast and non broadcast (custom) standard specific lines and on analog high-definition TV formats (1080i, 1080p, 720p, 480p). The TDS3VID or TDS3SDI application module is required. |
| Pulse width (or burr) |
It can be triggered on a pulse width less than, greater than, equal to or not equal to the optional time limit range (39.6 ns - 50 s). |
| Underamplitude pulse |
It can be triggered on a pulse passing through a threshold, but cannot pass through the second threshold before passing through the threshold again. |
| Conversion rate |
It can be triggered at a pulse edge rate faster or slower than the set rate. It can be a rising edge, a falling edge, or both. |
| Code type |
Specify AND, OR, NAND, NOR when it is true or false at a specific time. |
| state |
Any logical state. The rising or falling edge of the clock can be triggered. You can use logic triggers on a combination of two inputs instead of four. |
| signal communication |
Provide the required isolation pulse trigger function for DS1/DS3 communication template test according to ANSI T1.102 standard. TDS3TMT application module is required. |
| alternate |
Use each active channel as the trigger source in order. |
measurement system
| cursor |
Range, time. |
| Automatic waveform measurement |
-Display the waveform measurement values of four arbitrary combinations. Or use the measurement snapshot function to display all measurement data. Measurement items include: cycle, frequency, width, - width, rise time, fall time, duty cycle, - duty cycle, overshoot, - overshoot, high, low, large, small, peak to peak, amplitude, average, average cycle, root mean square, root mean square of cycle, burst width, delay, phase, area * 1, cycle area * 1 |
| Measurement statistics |
Average, small, large, standard deviation. The TDS3AAM application module is required. |
| threshold |
User defined automatic measurement threshold, which can be set by percentage or voltage. |
| Strobe |
You can use the screen or vertical cursor to isolate specific events that occur inside the collection for measurement. |
Waveform mathematical operation
| Algebraic operation |
Add, subtract, multiply, divide waveforms. |
| FFT |
Spectrum amplitude. Set the FFT vertical scale to linear RMS or dBV RMS, and set the FFT window to Rectangular, Hammering, Hanning, or Blackman Harris. |
| Advanced mathematical operation * 1 |
Integral, differential, and widely defined algebraic expressions, including analog waveforms, mathematical functions, scalars, two more user adjustable variables, and parameter measurement results. Example: (Intg (Ch1 Mean (Ch1)) x 1.414 x VAR1). |
Waveform processing
| Automatic setting |
On the vertical, horizontal and trigger systems, one key can automatically set all channels, and the automatic setting function can be cancelled. |
| Offset correction |
The offset correction value between channels (± 10ns) can be input manually to obtain better timing measurement value and more accurate mathematical waveform. |
Display characteristics
| Display Type |
6.5 inch (165.1 mm) LCD TFT color display. |
| Display resolution |
640 pixels horizontal x 480 pixels vertical (VGA). |
| Interpolation |
Sin(x)/x |
| Waveform style |
Point, vector, variable afterglow, infinite afterglow. |
| Markings |
Full standard, grid, cross line, frame, NTSC, PAL, SECAM and oscilloscope (100% and 75% color bar vectors) require TDS3VID and TDS3SDI video application modules. |
| format |
YT, XY and gated XYZ (XY with Z-axis blank display is only available on 4-channel instruments). |
Power Supply
| AC power supply |
|
| supply voltage |
100 VRMS- 240 VRMS± 10%。 |
| Power frequency |
45 Hz - 440 Hz at 100 V-120 V; 45 Hz - 66 Hz at 120 V - 240 V. |
| energy consumption |
Large 75 W. |
| Power supply |
Requires TDS3BATC rechargeable lithium battery |
| Typical working hours |
3 hours |
Environment and safety work Non work
| temperature |
0 º C to 50 º C |
-40 º C to 71 º C |
| humidity |
Working and non working humidity: when the temperature is less than or equal to 30 ℃, the relative humidity is 95% higher; Working and non working humidity: when the temperature is less than or equal to 50 ℃, the relative humidity is 45% higher. |
| height |
3000m |
15000m |
| electromagnetic compatibility |
Meet or exceed EN55011A radiation and conducted radiation standards; EN6100-3-2 AC power line harmonic radiation; EN6100-3-3 Voltage variation, fluctuation and flicker; FCC 47CFR, Part 15, Subpart B, Class A equipment; Australian EMC outline provisions. |
| security |
UL61010B-1, CSA1010.1, IEC61010-1, EN61010-1 |
Physical characteristics
| instrument |
| External dimensions |
millimeter |
inch |
| width |
three hundred and seventy-five |
fourteen point eight |
| height |
one hundred and seventy-six |
six point nine |
| thickness |
one hundred and forty-nine |
five point nine |
| weight |
kg . |
pound |
| Net weight of instrument |
three point two |
seven |
| Install the battery |
four point five |
nine point eight |
| Instrument delivery |
| Packaging appearance dimension |
millimeter |
inch |
| width |
five hundred and two |
nineteen point eight |
| height |
three hundred and seventy-five |
fourteen point eight |
| thickness |
three hundred and sixty-nine |
fourteen point five |
| Rack mount (RM3000) |
| External dimensions |
millimeter |
inch |
| width |
four hundred and eighty-four |
nineteen |
| height |
one hundred and seventy-eight |
seven |
| thickness |
one hundred and fifty-two |
six |
*1 TDS3AAM module is required. |
